DOCUMENTATION

Declaration of Performance

No.

001DO2011-01-01

Valid from:

01.01.2014

1. Identification:

Pre-fabricated brick beams [masonry beams/ single lintel]

2. Type:

Pre-stressed brick beams with 3, 4, 5, and 6 layers with their own load capacity.

It refers to beams with their own geometry and static calculation.

See dimensions 

3. Use:

Above openings in brick walls and dividers, in bearing and non-bearing brick structures.

4. Producer:

Carlsberg Bjælker A/S, Tindbækvej 16, DK-8830 Tjele

5. Authorised agent:

Not relevant

6. System (AVPC)

3

7. Notified body:

The Institute for Technology (No. 1235) performed the verified type test of the load capacity during the calculation phase. This was documented in the following document:

Pre-fabricated Masonry Beams: 1313606-06-09.

8. European technical evaluation:

Not relevant

9. Performance:

Important features

Performance

Harmonised technical specification

Load capacity
(after deciding that the data will be specified under ”additional data”)

kN/m

See strength diagram

EN 845-2:2013

Inclination.

mm

See deformation table

Water vapour permeability

N/A

Water vapour permeability

N/A

Direct airborne noise insulation

N/A

Mass for surface unit 

To insert in the formula - see Geometry (*1)

kg/m²

= 2000 * B [m]

(B=Bredde)

Heat insulation performance

N/A

Fire resistance

See code for brand plates below

See brand plates

Resistance against corrosion

See brand plates

Resistance against frost

See brand plates

10. The declared performance for the merchandise specified in points 1 and 2 corresponds to the performance declared in point 9. 

This declaration of performance has been prepared under the sole responsibility of the producer mentioned in point 4. 

Signed for the producer and in his name:

Jens Peter Madsen, General Manager

Randers d. 1/1-2014

Declaration of Performance

No

001DO2011-01-01

Valid from:

01.01.2014

1. Identification:

Composite brick lintel

2. Type:

Pre-stressed or lightly reinforced brick lintel with 1, 2 or 3 layers.

Consists of lintels with lengths of 0.71 - 5.99 m.

See schematics

3. Use:

Above openings in brick walls and dividers in bearing and non-bearing brick structures.  

4. Producer:

Carlsberg Bjælker A/S, Tindbækvej 16, DK-8830 Tjele

5. Authorised agent::

Not relevant

6. System (AVPC)

3

7. Notified body:

The Institute for Technology (No. 1235) performed the verified type test of the load capacity of lintels during the calculation phase. This was documented in the following document:     
Brick lintels: 1316346-13/258605.

8. European technical evaluation:

Not relevant

9. Performance:

Important features

Performance

Harmonised technical specification

Load capacity
(after deciding that the data will be specified under ”additional data”)

kN/m

See strength diagram

EN 845-2:2013

Inclination.

mm

See deformation table

Water absorption

N/A

Water vapour permeability

N/A

Direct airborne noise insulation

N/A

Mass for surface unit 

To insert in the formula - see Geometry (*1)

kg/m²

2000 * B [m]

(B=Bredde)

Heat insulation performance

N/A

Fire resistance

See code for brand plates below

See brand plates

Resistance against corrosion

See brand plates

Resistance against frost

See brand plates

10. The declared performance for the merchandise specified in points 1 and 2 corresponds to the performance declared in point 9. 

This declaration of performance has been prepared under the sole responsibility of the producer mentioned in point 4.

Signed for the producer and in his name:

Jens Peter Madsen, Direktør

(name and position)

Randers d. 1/1-2014